Friday, 25 September 2009

Some Progress!

At last some progress. I have had a few hours in the garage and have started to make some progress. It has been disturbed by the need to do a lot of work on my enduro bike for a 2 day rally in a couple of weeks time, but it has been good experience for me, including fitting new wheel bearings in the front wheel. I know to most it is very easy, but I have never done it before and am having to learn stuff from scratch, generally with help of a couple of excellent forums;


How did we cope before the Internet arrived?
Anyway I have been busy with the angle grinder and my wife's jewelry polishing machine, very handy!

I have taken off the rear foot rest mountings. More tricky than I expected. Angle grinders are very vicious so you have to be really careful not to cut into anything that needs to stay intact, like a load bearing piece of frame for example. I think I made fairly decent job of it, not too much extra damage!












Next were the front forks. I am not doing a great deal to them other than give them a decent clean out and refresh the oil, and give them a damn good clean and polish. Elbow grease to the for.... I would like to run them with the upper springs exposed, or visible under clear fork gaitors. So perhaps some nice new shiny springs would look good?
I have discovered the best way to prepare for polishing seems to be by hand, especially where there are fiddly places to get to. Elbow grease and constant supply of fresh wet and dry. Start off with the gritty stuff, and work down to the fine stuff. I have just spent about £9 on polish and polishing mops from http://www.thepolishingshop.co.uk/, as my wife went mental when she saw what I had done to her jewelry stuff!

I still need to order the seat and a new front mudguard from the US. I was quoted about £40 for postage, but a seat and a mudguard for about £150 doesn't seem to bad. I will still have to wait for pay day though. Actually it is quite a lot of cash when you consider I only paid £155 for the whole bike...
I have salvaged the brackets from the old front mudguard, and will need to tidy those up a bit, but at least that will save some time and money, and at least they will fit. I might even get them chromed?




I need to get hold of some half decent new shocks for the bike too. The original ones are rubbish. I am struggling to find something that will fit, the 'leg length' seems to be the problem. There needs to be enough of a gap between the swing arm mounting point and where the spring starts so that the shock clears the chain. I was disappointed that Hagon were unable or unwilling to help. There are some Betor ones that will fit, but I have read somewhere that there quality is questionable. The hunt continues...

Thursday, 16 July 2009

Chassis work

Now the bike is in bits it seems like the most logical place to start is the chassis. I have a list of jobs that need to be done and parts to be sourced.

The rear footrests and brackets need to come off, so out with the angle grinder. I am sure there are more subtle tools to use, but set an angle grinder to steel and it's like a fire-work going off! Note to self, move other bikes and fuel cans out of the way.

Source 1960's style bubble seat. It looks like I am going to have to order from the US - Airtech seem to do many different designs that will fit. They also do mudguards so I will probably get one of those will I am at it. Fitting the seat will be my first challenge as I imagine I will have to fabricate some new brackets and weld them on. Hacksaw - check, small selection of metal files - check, vice - check, welder and welding skills.... erm no.

The standard rear shocks just seem to be springs, so I will see if Hagon do something that actually functions as a damper that will fit

I would love to stick a new front end on, but I would imagine the required skills are going to be beyond me at this stage, so I will do the best I can with the standard forks. Apparently they work best with engine oil rather that fancy fork oil! The springs are on the outside, hidden by a rubber boot. I will see if I can polish them up and make them look half decent. It would be nice to have a disk on the front, but I will stick with the original drums for now.

Rear brake light and reg plate holder, going to need one, as inconspicuous as possible...

Bin the rear mudguard and centre stand.

Straighten the front foot pegs.

I guess once that is all done I can send it off for powder coating or painting? A nice shiny black I think.

Now where is the angle grinder?

Wednesday, 15 July 2009

From this to this...

The idea of this blog is to help people like myself, with no real experience, to learning how to renovate/customise a 'vintage' motorbike.

The idea is to go from this (a 1975 Honda CB125S, non-runner);















To this (a very beautiful 1960's Honda race bike);















Now I know an old Honda CB125 that cost 150 quid is never going to look like a classic, expertly restored beauty like the one above, but the idea is to make a good effort and to learn all the relevant skills, or find the relevant expertise when needed so that for the next project I can confidently move on to bigger and better things.

Right now I have the bike stripped and in many parts in the garage. I have some plans and ideas, which I will share in the next blog, but very little idea or the technical expertise to make them happen. So my plan is to take it a step at a time and give it a go. It's gonna take some time, but here we go...